Forum
EasyIoT Cloud
Bug reports
ESP crashes
ESP crashes
Less
More
Posts: 2
Thank you received: 0
7 years 10 months ago - 7 years 10 months ago #3652
by hacajd
Yes folks,I try
ESP8266 internet connected switch V1 exactly with this
this
.
device succesfully connect on router and switch ESP from AP to STA .
then all crashes.
as node I used kit ESP8266MOD as we reccomend in TOH.And looks same.On the bottom I read ESP12E DEVKIT.
Is there any problems with this piece of HW???
I may send debug dump if need.
I plan another experiment with ordered esp01 but FTDI not come to this time then wait on it.On esp chip I read ESP8266EX. Its OK?
I dont know,FW is allready rewrited-YES? when i burn the project.
External flash type? ESP chip HW vers. I dont know.God know and someone else may.
Last edit: 7 years 10 months ago by
hacajd .
Please Log in or Create an account to join the conversation.
Less
More
Posts: 862
Karma: 25
Thank you received: 264
7 years 9 months ago #3671
by EasyIoT
hacajd wrote: Yes folks,I try ESP8266 internet connected switch V1 exactly with this
this
.
device succesfully connect on router and switch ESP from AP to STA .
then all crashes.
as node I used kit ESP8266MOD as we reccomend in TOH.And looks same.On the bottom I read ESP12E DEVKIT.
Is there any problems with this piece of HW???
I may send debug dump if need.
I plan another experiment with ordered esp01 but FTDI not come to this time then wait on it.On esp chip I read ESP8266EX. Its OK?
I dont know,FW is allready rewrited-YES? when i burn the project.
External flash type? ESP chip HW vers. I dont know.God know and someone else may.
Can you post serial dump?
Please Log in or Create an account to join the conversation.
Less
More
Posts: 2
Thank you received: 0
7 years 9 months ago #3675
by hacajd
Here is it when I press key:
WiFi connected
IP address:
192.168.100.106
Connecting to MQTT server
MQTT client id:5c:cf:7f:1:64:90-7c
connected to MQTT server
ModuleId: 7
Suscribe: /7/Sensor.Parameter1
set state:
button pressed
set state:
Publish /7/Sensor.Parameter1 1
published.
disconnected. try to reconnect...
Exception (9):
epc1=0x40105050 epc2=0x00000000 epc3=0x00000000 excvaddr=0x00000003 depc=0x00000000
ctx: sys
sp: 3ffffd50 end: 3fffffb0 offset: 01a0
>>>stack>>>
3ffffef0: 00000011 00000020 3ffe84ab 3fff2954
3fffff00: 4010527c 004619eb 3ffeed48 00000000
3fffff10: 3ffee610 3ffeed48 3ffefe60 40204961
3fffff20: 00000000 0043b791 40201228 000001f4
3fffff30: 3ffeed48 3fff0608 3fff2954 402049d8
3fffff40: 3fff0608 3fff28dc 3ffeec3c 40201ec9
3fffff50: 3ffe88a3 40205264 00000014 40204d05
3fffff60: 00000000 00000000 00000000 40205285
3fffff70: 40221eba 00000000 3fff293c 40221ec8
3fffff80: 40100fe6 00000002 3fffdab0 00000000
3fffff90: 40207a22 3fffdab0 00000000 3fff0630
3fffffa0: 3fffdc60 00000000 3fffdab0 40000f49
<<<stack<<<
ets Jan 8 2013,rst cause:2, boot mode:(3,6)
Thank You.
Please Log in or Create an account to join the conversation.
Less
More
Posts: 862
Karma: 25
Thank you received: 264
7 years 9 months ago - 7 years 9 months ago #3677
by EasyIoT
hacajd wrote: Here is it when I press key:
WiFi connected
IP address:
192.168.100.106
Connecting to MQTT server
MQTT client id:5c:cf:7f:1:64:90-7c
connected to MQTT server
ModuleId: 7
Suscribe: /7/Sensor.Parameter1
set state:
button pressed
set state:
Publish /7/Sensor.Parameter1 1
published.
disconnected. try to reconnect...
Exception (9):
epc1=0x40105050 epc2=0x00000000 epc3=0x00000000 excvaddr=0x00000003 depc=0x00000000
ctx: sys
sp: 3ffffd50 end: 3fffffb0 offset: 01a0
>>>stack>>>
3ffffef0: 00000011 00000020 3ffe84ab 3fff2954
3fffff00: 4010527c 004619eb 3ffeed48 00000000
3fffff10: 3ffee610 3ffeed48 3ffefe60 40204961
3fffff20: 00000000 0043b791 40201228 000001f4
3fffff30: 3ffeed48 3fff0608 3fff2954 402049d8
3fffff40: 3fff0608 3fff28dc 3ffeec3c 40201ec9
3fffff50: 3ffe88a3 40205264 00000014 40204d05
3fffff60: 00000000 00000000 00000000 40205285
3fffff70: 40221eba 00000000 3fff293c 40221ec8
3fffff80: 40100fe6 00000002 3fffdab0 00000000
3fffff90: 40207a22 3fffdab0 00000000 3fff0630
3fffffa0: 3fffdc60 00000000 3fffdab0 40000f49
<<<stack<<<
ets Jan 8 2013,rst cause:2, boot mode:(3,6)
Thank You.
ESP8266 crashes after it publish value. It seems that it is disconnected from EasyIoT Cloud. How many modules do you have configured in EasyIoT Cloud? Maybe you exceed maximum number of modules for your account? You can see account limits under Configure->Account limits.
Also check if module #7 exists in module list.
Last edit: 7 years 9 months ago by
EasyIoT .
Please Log in or Create an account to join the conversation.
Forum
EasyIoT Cloud
Bug reports
ESP crashes
Time to create page: 0.285 seconds