Beta V0_8bX

5 years 3 months ago #1136 by cdj
Thanks for new improvements! No iframe in categories?
The topic has been locked.
5 years 2 months ago - 5 years 2 months ago #1138 by osalval
Thank you very much.

Finally i started to control my Roller shutter :) with EasyIoT.

Only to comment that when I add the Node it appeared as S_GENERIC instead S_COVER, but V_UP, V_STOP and V_UP works.

Now I have to figure up how to use it with V_DIMMER.
The topic has been locked.
5 years 2 months ago #1144 by EasyIoT

osalval wrote: Thank you very much.

Finally i started to control my Roller shutter :) with EasyIoT.

Only to comment that when I add the Node it appeared as S_GENERIC instead S_COVER, but V_UP, V_STOP and V_UP works.

Now I have to figure up how to use it with V_DIMMER.


I will check. I didn't tested, because I do not have roller shutters.
The following user(s) said Thank You: osalval
The topic has been locked.
5 years 2 months ago - 5 years 2 months ago #1146 by osalval

EasyIoT wrote:

osalval wrote: Thank you very much.

Finally i started to control my Roller shutter :) with EasyIoT.

Only to comment that when I add the Node it appeared as S_GENERIC instead S_COVER, but V_UP, V_STOP and V_UP works.

Now I have to figure up how to use it with V_DIMMER.


I will check. I didn't tested, because I do not have roller shutters.

OK.
In my case, Roller Shutter control is really a 2 relays control (DigitalOutput). For instance:
Relay 1 active means Arduino Incoming message with V_DOWN=1. So => Arduino DO 4 = 1 and DO 5 = 0
Relay 2 active means Arduino Incoming message with V_UP=1. So => Arduino DO 5 = 1 and DO 4 = 0
Both desactives means Arduino Incoming message with V_STOP=1. So => Arduino DO 4 = 0 and DO 5 = 0
I know it is very basic but I am not a coder. :lol:

Doing more tests. After add Node I get 3 rows. I think because I have 3 S_COVER presentation messages:
gw.present(CHILD_ID_REL1, S_COVER);
gw.present(CHILD_ID_REL_OFF, S_COVER);
gw.present(CHILD_ID_REL2, S_COVER);
MyMessage msgREL_2(CHILD_ID_REL1, V_DOWN);
MyMessage msgREL_1(CHILD_ID_REL_OFF, V_STOP);
MyMessage msgREL_0(CHILD_ID_REL2, V_UP);

Best presentation will be 1 only row for the 3 possible states and another line for V_DIMMER control.
The topic has been locked.
5 years 2 months ago #1147 by EasyIoT

osalval wrote:

EasyIoT wrote:

osalval wrote: Thank you very much.

Finally i started to control my Roller shutter :) with EasyIoT.

Only to comment that when I add the Node it appeared as S_GENERIC instead S_COVER, but V_UP, V_STOP and V_UP works.

Now I have to figure up how to use it with V_DIMMER.


I will check. I didn't tested, because I do not have roller shutters.

OK.
In my case, Roller Shutter control is really a 2 relays control (DigitalOutput). For instance:
Relay 1 active means Arduino Incoming message with V_DOWN=1. So => Arduino DO 4 = 1 and DO 5 = 0
Relay 2 active means Arduino Incoming message with V_UP=1. So => Arduino DO 5 = 1 and DO 4 = 0
Both desactives means Arduino Incoming message with V_STOP=1. So => Arduino DO 4 = 0 and DO 5 = 0
I know it is very basic but I am not a coder. :lol:

Doing more tests. After add Node I get 3 rows. I think because I have 3 S_COVER presentation messages:
gw.present(CHILD_ID_REL1, S_COVER);
gw.present(CHILD_ID_REL_OFF, S_COVER);
gw.present(CHILD_ID_REL2, S_COVER);
MyMessage msgREL_2(CHILD_ID_REL1, V_DOWN);
MyMessage msgREL_1(CHILD_ID_REL_OFF, V_STOP);
MyMessage msgREL_0(CHILD_ID_REL2, V_UP);

Best presentation will be 1 only row for the 3 possible states and another line for V_DIMMER control.


You should use one CHILD_ID and not three.
The following user(s) said Thank You: osalval
The topic has been locked.
5 years 2 months ago #1149 by osalval
Done, thank you EasyIoT

Now I have only 1 row with Roller Shutter control.

But still it is detected as S_GENERIC.

If I don't change it, it shows values defined in Parameters.
Sensor.CoverLevel
Sensor.Down
Sensor.Stop
Sensor.Up

And, if after, I change it to Roller Shutter (A0,D0), it shows only "Sensor.CoverLevel" Parameter (first one)

Maybe because S_COVER it is not detected?

I think it is important to show status of Roller Shutter
The topic has been locked.
Time to create page: 0.224 seconds

Forum latest

  • No posts to display.